Search
Filters
Close

ATOMIUM “MGSB 100”

$34.99
Eliminates transmission noise and vibration, conditions transmission seals, breaks down sludge, gum and varnish and helps fight rust and oxidation.

Atomium MGSB 100 is a transmission fluid conditioner for the treatment of manual transmission, rear axles, reduction gears. The treatment is completed in one stage.
Product size: 100ml.

TECHNICAL INFO

 

  • Recovers the optimal parameters of the shifts, eliminates “spurts” during gear shifts

  • Improves process of burnishing the manual transmission partsdue to the adaptive properties of the LC, that work on optimization of conjugated friction parts

  • Protects transmissions and increases the lifetime of AGSB and variators in 1,5-2 times due to wear intensity decreasing

  • Decreases friction losses in transmission partsdue to improvement of the friction mode

  • Completely safe for clutches

  • Maximum protection for the automatic transmission and variators against wear in the maximum loadings and high temperatures

  • Completely safe for gaskets, seals or any other parts made of of rubber

  • Decreases noise and vibration levels due to forming of thick and resistant lubrication “pillow” and clearances optimization

  • Restores optimum spacing in bearings and serrated gearings

DIRECTIONS

 

Warm up the transmission by driving the vehicle for at least a few minutes. Shut the engine off. Add Atomium MGSB 100 to existing fluid.
Use 30ml of  product per each liter of the total transmission fluid capacity.

Drive the vehicle for at least 20 minutes after adding transmission fluid additive. Operate the car normally until the next regular transmission fluid change.

 

 

 

Important Info:

  • Before applying Atomium MGSB 100 shake the can thoroughly until natural sediments (active components) are totally dissolved.
  • Apply Atomium MGSB 100 through the regular dipstick hole of the warmed-up transmission.
  • Drive the vehicle for at least 20 minutes in any mode (regular operation) after applying Atomium MGSB 100.
  • It is recommended to carry out Atomium treatment of automatic transmissions together with engine processing at the same time or sequentially.
  • It is not recommended to apply the lubricant if you know of any mechanical issues with the parts and assemblies of your transmission.
  • Atomium MGSB 100 is compatible with any type of transmission oils ATF – Synthetic Automatic Transmission Fluid (the red oil) and doesn’t change their properties.
  • To maximize protection of the unit it is recommended to apply further after each oil change in transmission (every 30,000 – 45,000 ml).

 

 

Atomium MGSB 100 is a transmission fluid conditioner for the treatment of manual transmission, rear axles, reduction gears. The treatment is completed in one stage.
Product size: 100ml.

TECHNICAL INFO

 

  • Recovers the optimal parameters of the shifts, eliminates “spurts” during gear shifts

  • Improves process of burnishing the manual transmission partsdue to the adaptive properties of the LC, that work on optimization of conjugated friction parts

  • Protects transmissions and increases the lifetime of AGSB and variators in 1,5-2 times due to wear intensity decreasing

  • Decreases friction losses in transmission partsdue to improvement of the friction mode

  • Completely safe for clutches

  • Maximum protection for the automatic transmission and variators against wear in the maximum loadings and high temperatures

  • Completely safe for gaskets, seals or any other parts made of of rubber

  • Decreases noise and vibration levels due to forming of thick and resistant lubrication “pillow” and clearances optimization

  • Restores optimum spacing in bearings and serrated gearings

DIRECTIONS

 

Warm up the transmission by driving the vehicle for at least a few minutes. Shut the engine off. Add Atomium MGSB 100 to existing fluid.
Use 30ml of  product per each liter of the total transmission fluid capacity.

Drive the vehicle for at least 20 minutes after adding transmission fluid additive. Operate the car normally until the next regular transmission fluid change.

 

 

 

Important Info:

  • Before applying Atomium MGSB 100 shake the can thoroughly until natural sediments (active components) are totally dissolved.
  • Apply Atomium MGSB 100 through the regular dipstick hole of the warmed-up transmission.
  • Drive the vehicle for at least 20 minutes in any mode (regular operation) after applying Atomium MGSB 100.
  • It is recommended to carry out Atomium treatment of automatic transmissions together with engine processing at the same time or sequentially.
  • It is not recommended to apply the lubricant if you know of any mechanical issues with the parts and assemblies of your transmission.
  • Atomium MGSB 100 is compatible with any type of transmission oils ATF – Synthetic Automatic Transmission Fluid (the red oil) and doesn’t change their properties.
  • To maximize protection of the unit it is recommended to apply further after each oil change in transmission (every 30,000 – 45,000 ml).